PHASE 08 ยท PRODUCTION READY

Production ready.
A smooth start at your manufacturer.

You arrive with a validated design. You leave with a product your manufacturer can build and test the same way every time, in Europe or Asia, with approved samples to prove it.

Henrik Andersen development loop: enter anywhere, stay as long as you need, exit anytime

At a glance.

You bring
  • A validated design
  • Target volumes and price
  • Preferred regions or partners
  • Or a product that is hard to build
I do
  • DFM / DFA review
  • EMS selection and sourcing
  • Test jig and test firmware
  • First article and pilot run
You get
  • Production data package
  • End-of-line test jig
  • Approved golden samples
  • Handover to production

What is included.

Ten building blocks. Take them all, or just the ones you need.

HOW PRODUCTION IS PREPARED

Design for manufacture, assembly and test.

The product is designed so it can be built, inspected, programmed and tested the same way every time, at your manufacturer, from the first batch to series production.

Design for manufacture, assembly and test. Top: the production flow, build (SMT and THT), inspect (AOI and X-ray), program (firmware and keys) and test (functional test). Middle: an example board in its panel with rails, tooling holes, fiducials, test points TP1 to TP5 and an SWD programming header, with the pogo pins of the test fixture underneath. Design rules applied: DFM, footprints and spacing to fab limits and panel, fiducials and tooling holes; DFA, one-side SMT where possible and polarity marks with fewer part types; DFT, a test point on every critical net and programming access in the fixture. Principles: designed for the line, known test coverage, program in one step, same result every unit. Right: the typical outputs, DFM, DFA and DFT reviews, test points, fixtures and production test specifications.

HOW ROBUSTNESS IS PROVEN

Reliability and robustness engineering.

Tolerances, ageing, thermal behaviour, electrical stress and failure mechanisms are evaluated, so the product keeps working across part spreads, temperatures and years of use.

Reliability and robustness engineering. Four example analyses: derating, with component stress against rating below an 80 percent limit; tolerance analysis, a Monte Carlo spread of the output voltage with all runs inside the lower and upper limits; an FMEA with the risk priority of three failure modes reduced after action, for example connector fretting from 168 to 42; and reliability testing on a bathtub curve of failure rate over product life, with burn-in, temperature cycling and HALT. Stresses evaluated: tolerances, ageing, thermal, electrical stress and failure mechanisms. Right: the typical outputs, derating analysis, tolerance analysis, FMEA and reliability test results.

HOW PRODUCTION IS HANDED OVER

Release and production transfer.

Your manufacturer receives a complete, reproducible product definition: one released package from which every unit can be built, programmed and tested, proven in a pilot build before series production.

Release and production transfer. An example release package under one frozen baseline, R1.0, with five items, each with its version, how it was verified and its status: fabrication and assembly data, rev C, checked by Gerber compare; approved BOM and drawings, rev C, checked against CAD; the firmware programming image with bootloader and application, v1.0.0, with its sha256 checksum; work instructions and test specification, rev B, tried on the line; and the pilot-build report, reviewed and signed. Below: the transfer steps, baseline frozen, pilot build, series release, with one tag for hardware, firmware and documents; and an example pilot build of 50 units with a first-pass yield of 94 percent and 3 findings, actions closed before series. Principles: reproducible from the package alone, one tagged baseline, pilot before series, nothing undocumented. Right: the typical outputs, release package, programming images, work instructions and pilot-build results.

What you get.

Production BOM With approved vendor list
Data package Gerber, assembly, drawings
Test jig End-of-line test + firmware
FAI report First article inspection
Golden samples Approved reference units
Work instructions Assembly and labelling

For PCB fabrication, assembly and series production I work closely with providers such as Eurocircuits, AISLER, PCBWay, Zhen Ding Technology and Foxconn.

Duration

Agreed in your proposal

Enter with

A validated design

Exit with

Start of production

Payment

After your approval

Where to next.

Continue with me through the next phases to start of production, or leave with what you came for.

CONTACT

Ready to start at phase 08?
Or hand over the complete development? Just ask.

A new product to develop from scratch, a design that needs a second look, or a prototype that does not work yet: a few lines are enough to start.

  • A personal reply within one working day
  • No cost and no commitment up front: you only pay for work you approve
  • Your idea stays confidential, NDA on request (how I keep your project confidential)

Write to me

info@siliconmeetscode.com
Write an email

Helpful to mention: what the product does, where it is today, and your timeline. The email opens with these questions ready to fill in.

Working from Belgium and Germany with clients across Europe and Asia